FIX-A-LEAK is a blended concentrated material designed to seal leaks in virtually any material. It can be applied for leaks in the shell and works equally well in plumbing.
Minor drips or leaks usually require less product (8 ounce bottle). Depending on the severity of the leak, a 32 ounce bottle may be required. This would allow you to begin by using 1/3 of the bottle initially and if more product is required you can add the additional amounts.
We do not recommend using the spa until the leak is fixed and the remainder of FIX-A-LEAK is either filtered or drained from the spa/hot tub. If the leak has slowed but not totally stopped, you may add more FIX-A-LEAK to increase the strength of solution already in the spa/hot tub. You can then repeat steps 5-8 to further seal. IMPORTANT: Before doing so, stir the FIX-A-LEAK in the spa/hot tub with a soft broom to get existing solution back into suspension.
The product requires pressure to ensure it is impacted into the area of the leak.
Leaks created by a crack in the pipe, in all probability, will be sealed. However, the leak may re-occur due to vibration, which in turn, will migrate in size re-creating the leak. Also, what may occur over time is that, the expansion and contraction of the pipe may break the seal. In either case, a manual repair may be required.
Most spa/hot tubs are foam insulated and, when saturated with water, will greatly delay the cure time of FIX-A-LEAK. It would be best to drain the spa/hot tub and immediately wipe down the shell surface with a damp cloth to remove any residual of FIX-A-LEAK. Allow 3-5 days before refilling. In most cases, this will allow the product to cure.
Even if the foam insulation looks dry on the outside, the interior of the foam will remain wet or damp for many months.
In most cases, FIX-A-LEAK should be effective in sealing your leak for 1–2 years.
We do not recommend draining the spa/hot tub with prolonged freezing weather. If not drained properly, in all probability, you will end up with a cracked pipe causing a bigger problem. We would suggest filtering out the product with your cartridge filter. Run the spa/hot tub for a few hours then remove the cartridge filter and immediately rinse with warm or hot water to remove any FIX-A-LEAK residue.
Repeat this procedure a few times to ensure the product is removed from the spa/hot tub. This should get you through the winter with a 4-6 month seal. The treatment may have to be repeated in warmer weather when you can safely drain the spa/hot tub.
Bypass FILTER MEDIA before adding FIX-A-LEAK to water. Sand filters: set filter valve to recirculate. Other types: remove cartridges DE elements from filter tank. Then proceed to circulate through empty tank
With pump running, add FIX-A-LEAK slowly through skimmer or in front of any other suction intake.
After adding FIX-A-LEAK adjust suction to main drain. If this is not possible, the vacuum cleaner could be used alternatively, simply by placing the vacuum in deepest part of pool and connect to normal vacuum connection.
FIX-A-LEAK is very heavy and will sink to the lowest point rather quickly. It must be stirred back into suspension, either manually using a pool broom or mechnically with a automated pool cleaner every 4-6 hrs. during circulation of water.
Continue to recirculate water until the leak has stopped.
Mark level of water in pool and check for 2-3 days to determine if the leak has stopped.
After the leak has stopped and given the proper time to cure (24-48 hrs.) you may return to normal filtration. Sand Filters: Set filter valve to filter and resume normal operation. Backwash out unused FIX-A-LEAK as required.
Other Types: Reinstall filter into tank and resume operation. Rinse out unsed FIX-A-LEAK from filter as required.
*NOTE* Never let cartridges of DE elements be left to dry before they are cleaned.
Treatment can be repeated if necessary.
Suction Leaks are usually known by air mixed with the water at the return fittings. In most cases suction lines only leak water when the filter pump is shut off. Normal Circulation will simply draw FIX-A-LEAK away from the leak and if the pump is shut off the material will simply not get to the leak. You must reverse the flow of water, to force the material through the leak under pressure. Preferably 5-10 psi. untill the leak has stopped. When this has been achieved, gradually increase pressure to 15-25 psi. to insure a proper seal.
Keep Out Of Reach Of Children. Can cause severe eye and skin irritation. Do not get in eyes, on skin, or on clothing. Harmful or fatal if swallowed. Avoid contamination of food. Rinse empty container thoroughly with water and discard it.
In case of contact, immediately flush eyes or skin with plenty of water for at least 15 minutes. For eyes, contact a physician. Remove and wash contaminated clothing before reuse. If swallowed, drink milk, egg whites, gelatin solution. If these are not available, drink large quantities of water. Call a physician immediately.
Leviton 86593-EM Raintight While-in-use Weather Resistant Cover for 15 Amp Right Angle GFCI...$ 39.99
AquaMend Epoxy Putty Stick is a hand-kneadable, fast-setting, fiberglass-reinforced polymer compound for permanent...$ 11.99
Aladdin AS-200 (PS-200) Shaft Seal. Replaces: Advance 6c-200, Ampro 606-78, Aqua Flo FF-14...$ 6.99